Induction Hardening in Sangrur
Certified induction hardening for Sangrur’s agricultural-machinery, cycle-parts and light-engineering units — 58–62 HRC with controlled case depth, collected on a scheduled pickup route from our Ludhiana facility, around 75 km away.
Looking for dependable induction hardening in Sangrur? At Thakur Industries, we give Sangrur’s agricultural-machinery, cycle-parts and light-engineering units certified surface hardening to 58–62 HRC without the capital cost of owning a heat-treatment plant. Components are collected on a scheduled pickup route from our Ludhiana facility, roughly 75 km away, hardened to specification and returned with documented hardness reports.
// SANGRUR, PUNJAB //
Built for Sangrur’s Engineering Belt
Sangrur sits at the heart of Malwa’s farm economy, and its industry reflects that. The district is home to a busy cluster of agricultural-machinery and implement makers, a steady base of cycle-parts manufacturers feeding the wider Ludhiana–Malerkotla supply chain, and dozens of light-engineering and fabrication units in and around Sangrur, Dhuri and Malerkotla. These workshops turn out high volumes of wear-critical components, but very few of them run an in-house induction line — which is exactly the gap we fill.
Farm equipment lives a hard life: rotavator blades cut abrasive soil, thresher and chaff-cutter shafts spin under shock loads, and implement gear hubs grind season after season. Untreated, these parts wear out fast and come back as warranty complaints. Selective induction hardening puts a tough, wear-resistant skin exactly where it is needed while leaving the core tough enough to absorb impact — the single most cost-effective way to extend the service life of agricultural and cycle components made in Sangrur.
// COMPONENTS //
Sangrur Parts We Harden
From tractor implements to cycle drivetrains and small fabricated assemblies, we harden the components Sangrur’s units depend on most:
Agricultural Machinery
Rotavator blades & gear hubs, cultivator tynes, implement gearbox gears, PTO shafts
Cycle Parts
Axles, freewheel bodies, pedal spindles, small gears, chain sprockets
Light Engineering
Shafts, pins, cams, levers, splined hubs, fasteners and fabricated assemblies
// LOGISTICS //
~75 km from Ludhiana
Our induction workshop is in Ludhiana, about 75 km from Sangrur along a well-connected highway corridor. That proximity lets us run a scheduled pickup and delivery route through the Sangrur, Dhuri and Malerkotla belt rather than treating each job as a one-off courier run.
- Confirm your job on WhatsApp and we book a collection slot
- Components travel batched to keep freight per-piece low
- Hardened to spec at our Ludhiana facility with full QC
- Returned with HRC and case-depth documentation, 3–5 day cycle
For Sangrur units this means certified metallurgy without buying or running any equipment — and because the same route serves Dhuri, Malerkotla and Patiala, your batches move economically.
// WHY CHOOSE US //
Why Sangrur Units Choose Thakur Industries
Consistent 58–62 HRC
Repeatable hardness on every agri and cycle component, batch after batch.
Documented Quality
HRC and case-depth certificates with every batch for your buyers.
Scheduled Logistics
Batched pickup–delivery on the Sangrur route from Ludhiana, ~75 km.
No Plant Cost
Certified hardening as job work — no capital outlay for your unit.
// SPECIFICATIONS //
Hardening Specifications
| Surface Hardness | 58–62 HRC (controlled to spec) |
|---|---|
| Case Depth | 0.8 mm – 3.5 mm |
| Common Parts | Implement shafts, gears, rotavator blades, cycle axles, sprockets |
| Steel Grades | EN8, EN19, EN24, 4140, 20MnCr5 |
| Service Area | Sangrur, Dhuri, Malerkotla, Patiala |
| Logistics | Scheduled pickup from Ludhiana (~75 km) |
| Turnaround | 3–5 working days door-to-door (batch-dependent) |
| Testing | HRC verification, case-depth check, dimensional inspection |
Related Services
// NEARBY TOWNS //
Also Serving Around Sangrur
Sangrur Hardening FAQs
Learn more about the metallurgy of surface hardening from the ASM International heat-treatment resources.
Last updated: June 2026 · Thakur Industries, Ludhiana, Punjab
Ready to Harden Your Quality?
Contact us for a free consultation. Send your component details or drawings and get a quick quotation within 24 hours.